clutch plates sticking

Post Reply
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

clutch plates sticking

Post by trevair »

hi al clutch plates sticking on my commander just another long shot is there a way to free it off in situ the normal piston way of bang it in gear and clutch in roll back and forward dont work
iknow you may probbaly say stripping is best way to see condition but just trying to take for run prior to perhaps stripping and molly this wintereither this or restoring my mv agusta in my kitchen
also looking for cheap basket case classic not interpol
wish i had bought classic instead of commander loads of fibreglass to paint but will be something else agian when ive finished it
stay safe everybody trev
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

Re: clutch plates sticking

Post by trevair »

should say locked not sticking
Anthony Duffield
Site Admin
Posts: 300
Joined: Sun Aug 11, 2013 8:13 am

Re: clutch plates sticking

Post by Anthony Duffield »

Has the clutch ever been free?

If No strip it

If Yes, first check that the clutch actuating mechanism is correctly set, you might just be able to free it up by bump starting the bike pull in the clutch and use both brakes to try to stop the bike thus freeing the clutch

Either way its not a big job why not just get it to bits and clean each plate with scotch bright and brake cleaner

Good luck
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

Re: clutch plates sticking

Post by trevair »

hi anthony clutch always been stuck so its a strip down guess ill need clutch compressor looks simple enough
trev
johnbirchjar
moderator
Posts: 1632
Joined: Sat Mar 07, 2009 11:20 pm

Re: clutch plates sticking

Post by johnbirchjar »

Yep, you will need a clutch compressor,It is easy enough,but do take care as fingers can be lost,'(cos the pressure on the plates is somewhat fierce)J.B.
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

Re: clutch plates sticking

Post by trevair »

hi clutch stripped and plates cleaned with scotchbrite couple of plates denibbed
what i want to know is do i smear the plates with oil before inserting or do they go in dry
regards trev
johnbirchjar
moderator
Posts: 1632
Joined: Sat Mar 07, 2009 11:20 pm

Re: clutch plates sticking

Post by johnbirchjar »

I've put clutches back on a number of occasions and never thought to smear them with oil (seeing as they would get well oiled the first time the clutch was engaged)but if it makes you feel better go for it Very HappyJ.B.
Anthony Duffield
Site Admin
Posts: 300
Joined: Sun Aug 11, 2013 8:13 am

Re: clutch plates sticking

Post by Anthony Duffield »

I always rebuild with dry plates
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

Re: clutch plates sticking

Post by trevair »

clutch rebuilt and working fine puzzles me though plates came out freely yet clutch didnt work but anyway it is now
thanks all trev

next is leaking water cover
johnbirchjar
moderator
Posts: 1632
Joined: Sat Mar 07, 2009 11:20 pm

Re: clutch plates sticking

Post by johnbirchjar »

Leaking where?J.B.
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

Re: clutch plates sticking

Post by trevair »

The bottom of the left had casing the big dome
Trev
johnbirchjar
moderator
Posts: 1632
Joined: Sat Mar 07, 2009 11:20 pm

Re: clutch plates sticking

Post by johnbirchjar »

If it's where it the two faces meet,a good Gasket goo should fix it,(so long as both faces are nice and smooth and not buckled or damaged wink)J.B.
Anthony Duffield
Site Admin
Posts: 300
Joined: Sun Aug 11, 2013 8:13 am

Re: clutch plates sticking

Post by Anthony Duffield »

No need for anything other than the two O Rings, both available from ANL
johnbirchjar
moderator
Posts: 1632
Joined: Sat Mar 07, 2009 11:20 pm

Re: clutch plates sticking

Post by johnbirchjar »

Would they be the ones that fit round the water pump?(I did away with the manual one fitted by Norton used and a 'leclic one externally cool )J.B.
johnbirchjar
moderator
Posts: 1632
Joined: Sat Mar 07, 2009 11:20 pm

Re: clutch plates sticking

Post by johnbirchjar »

Would they be the ones that fit round the water pump?(I did away with the manual one fitted by Norton and used a 'leclic one externally cool )J.B.
Anthony Duffield
Site Admin
Posts: 300
Joined: Sun Aug 11, 2013 8:13 am

Re: clutch plates sticking

Post by Anthony Duffield »

Morning John I hope you are keeping well.

Looking at the pump there is a small O Ring at position approx. 11 o'clock and a larger O Ring at approx. 5 O'clock that's it no other joints or O Rings I have never found it necessary to use any silicon or anything like.

BR Tony
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

Re: clutch plates sticking

Post by trevair »

thanks guys i have a full set of o rings from anl
regards trev
trevair
moderator
Posts: 225
Joined: Sat Apr 17, 2021 9:27 am
Location: rawtenstall
Contact:

Re: clutch plates sticking

Post by trevair »

hi all
it was leaking from the outside round plate with the four bolts in, why they never used gaskets in owt i will never know, anyway ived removed cover cleaned both side and siliconed will refill tomorrow
trev
User avatar
Richard Negus
moderator
Posts: 1060
Joined: Mon Jun 18, 2007 5:11 pm
Location: Wilds of Lincolnshire

Re: clutch plates sticking

Post by Richard Negus »

Trev,
There should be an O-ring cord sitting in the groove in the primary cover. Leave the gap at the 12 o'clock position.
The round cover has a tapered outside which compresses the O-ring as the four screws are tightened.
R.
Just a bike-less old fogey now. Boo-hoo!
Post Reply